Guangdong Yiren Technology designs and manufactures bakery processing and packaging equipment in-house. The XYD-SJTDBZ is purpose-built for short shelf-life triangle sandwiches, bringing heat sealing, bag trimming, corner folding and tab application into a single machine. It is driven by a cam + servo combination and runs at 35–40 bags per minute. Sandwich size is set to the customer’s own product. Four design principles guide the build: parallel stations, precise positioning, continuous stability, parameterized operation.
Core Strengths
Multi-station parallel operation — the cycle no longer waits on its slowest step
Conventional corner-fold packers use a single-station serial layout: sealing waits for trimming, trimming waits for corner folding, corner folding waits for tab application. Every process queues behind the one before it, so the machine cycle equals the sum of all process times.
The XYD-SJTDBZ uses a multi-station design. Heat sealing, bag trimming, corner folding and tab application run simultaneously at different stations, with the product flowing continuously from one to the next. The cycle is set by the slowest single process, not by the total of all of them, and idle waiting between stations is eliminated.
What this means for the buyer: a measured output of 35–40 bags per minute (2,100–2,400 bags per hour); fewer machines and fewer operators for the same output.
Cam + servo combination — stable corner folds and repeatable tab position
The real difficulty in triangle sandwich packaging is the corner fold: three corners must fold symmetrically and lie flat, and the tab must land in a fixed position. Purely pneumatic systems drift in timing when air pressure fluctuates. Purely mechanical cam systems time accurately but are slow and awkward to adjust when the format changes.
This machine combines both. The cam handles mechanical synchronization of the motion sequence; the servo handles positioning accuracy, with servo motors paired to precision planetary reducers. The result is high positioning accuracy and strong multi-station coordination.
What this means for the buyer: consistent corner folds, a fixed tab position, and less rework and waste from skewed corners or drifting tabs.
Built for short shelf-life products — continuous running and cleanable structure
Short shelf-life sandwiches mean short expiry, many batches and frequent changeovers. The machine has to run for long stretches and also be quick to clean, otherwise residue carries over into the next batch.
The body is predominantly stainless steel: a 201 stainless platform plate at 6.0 mm, a frame of 50×50×1.8 stainless square tube, and stainless steel product guides and side panels. The guard uses 6 mm PC sheet, the conveyor is food-grade blue PU flat belting, and rodent mesh is fitted. The product guides are removable, which makes it practical to clean the corner-folding stations and the glue path.
What this means for the buyer: uninterrupted production, faster end-of-shift cleaning, and a structure that meets food-contact hygiene requirements.
Parameterized operation — format changes without a veteran operator
The traditional barrier with corner-fold packers is setup: corner position, tab length and sealing temperature are all found by trial and experience.
This machine pairs a Fanyi touch screen with a Huichuan PLC, turning corner dimensions, tab position, sealing temperature and running speed into savable parameters. When the format changes, the operator loads the recipe and fine-tunes, rather than starting from scratch.
What this means for the buyer: shorter changeover time, new operators can work from the parameter sheet, and less dependence on skilled staff.
Three Steps to a Repeatable Run
Step 1: Startup checks and parameter setup
- Confirm air supply reaches 0.8 MPa and the air circuit has no leaks;
- Check conveyor belt tension, and inspect the blue PU belt surface for debris or adhesive residue;
- Check that the product guides are locked and set for the current format;
- Load the matching product recipe on the touch screen and confirm corner dimensions, tab position and sealing temperature;
- Dry-run 3–5 cycles and confirm the station sequence before feeding product.
Step 2: Feeding and production
- Place each triangle sandwich into the infeed in the locating direction, with the triangle point facing the same side;
- The machine runs heat sealing → bag trimming → corner folding → tab application, with all stations acting in sync;
- Inspect the first piece for three things: corners symmetric and flat, tab applied straight and pressed down, seal closed and firm;
- During continuous production, sample every 30 minutes for corner fold and tab position.
Step 3: Shutdown and cleaning
- Stop feeding and let all product inside the machine exit before shutting down;
- Power off and close the air supply;
- Remove the product guides and conveyor belt, and clear adhesive residue and crumbs from the corner-folding stations, glue path and sealing jaw;
- Clean the sealing jaw only after it has cooled; never scrape it with a sharp tool;
- Refit the guides, restore belt tension, and complete the inspection record.
Troubleshooting Common Faults
On a machine running at high intensity for long shifts, occasional faults are hard to avoid. Knowing how to diagnose these four common issues keeps the line from stopping.
Fault 1: Corners fold unevenly and the triangle is not symmetric
Likely causes: product not located correctly at infeed; product guides loose or shifted; servo synchronization fault leaving the fold stroke incomplete.
What to do:
- Stop the machine and check the infeed station — confirm the triangle points face the same way and no product is skewed;
- Re-lock the product guides and recalibrate their position for the current format;
- Check the touch screen for a servo alarm, clear it, then dry-run to recalibrate the phase.
Fault 2: Tab will not hold, or the tape runs off position
Likely causes: uneven tape tension or tape off its track; press roller not pressing firmly; oil or moisture on the bag surface; sealing temperature too low so the bag mouth never closes.
What to do:
- Adjust tape tension and check the guide rollers for binding or the tape sitting outside its groove;
- Check press roller pressure and cleanliness, and clear adhesive build-up;
- Confirm the sealing jaw reaches its set temperature and the bag mouth closes fully before tabbing.
Fault 3: Seal is weak, or the film is burnt through
Likely causes: sealing temperature set too high or too low; air pressure below 0.8 MPa so the jaw does not press firmly; adhesive residue on the jaw face causing uneven heat transfer.
What to do:
- Reset sealing temperature to suit the film and run a small trial batch to confirm;
- Check that air pressure holds at 0.8 MPa and inspect the air circuit for leaks;
- Stop, let the jaw cool, clear residue from the surface and check the sealing cloth for damage.
Fault 4: Alarm shutdown during running, or stations out of sync
Likely causes: servo drive alarm; photoelectric or proximity sensor blocked by debris; air pressure fluctuation leaving a cylinder short of stroke; cam phase shifted.
What to do:
- Read the alarm code on the touch screen and trace it to the specific station;
- Clean the sensing faces of the photoelectric and proximity switches and confirm their indicators;
- Check air pressure and solenoid valve action to rule out fluctuation;
- Reset the servo alarm and dry-run; if it recurs, check cam phase and mechanical binding.🧩 Wrap-Up!
The XYD-SJTDBZ is not about making any single step faster. It is about running four processes — heat sealing, bag trimming, corner folding and tab application — in parallel on one machine: the cycle is set by the slowest station rather than the sum of all four, corner-fold and tab positions are held stable by the cam + servo drive, and changeovers come from saved parameters instead of trial runs. For short shelf-life triangle sandwiches, where seal strength, corner symmetry and appearance consistency all matter, what the machine delivers is consistency and repeatability — the first bag and the ten-thousandth look like they came off the same machine.

